{"id":10038,"date":"2026-02-16T20:03:33","date_gmt":"2026-02-16T20:03:33","guid":{"rendered":"https:\/\/www.swisspointofcare.com\/sin-categoria\/syph-check-1\/"},"modified":"2026-03-05T06:56:41","modified_gmt":"2026-03-05T06:56:41","slug":"syph-check-1","status":"publish","type":"post","link":"https:\/\/www.swisspointofcare.com\/es\/kb\/syph-check-1\/","title":{"rendered":"Syph-Check-1"},"content":{"rendered":"\t\t
\n\t\t\t\t
\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Rapid self-test for the detection of antibodies against Treponema pallidum in blood<\/h3>\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t\t

Intended Purpose<\/h2>\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

SYPH-CHECK-1\u00ae is a manual qualitative immunochromatographic screening test for the detection of antibodies against Treponema pallidum from a finger prick whole blood sample. It can be used at home by lay users for self-testing for the detection of possible Syphilis infection.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t

General Points<\/h2>\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Syphilis is a veneral disease that progresses through distinct stages of infection: primary, secondary, latent and tertiary.<\/p>

These stages produce diverse clinical symptoms, typically producing initial sores known as chancres then syphilitic rash followed by long periods of dormancy. Untreated infection eventually leads to cardiovascular problems and neurosyphilis.
Caused by spirochaete Treponema pallidum (TP), the infection is usually acquired by sexual contact, although the disease may be transmitted by transfusion of infected blood. Intrauterine infection also occurs. The organism has proved virtually impossible to culture in artificial media, and diagnosis of the infection usually depends on the detection of antibodies in the blood, which appear soon after initial infection.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t\t\t\t
\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t

Test Procedure<\/h2>\t\t\t\t<\/div>\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t

Prepare everything properly before starting the testing procedure. Place the content of the box on a clean, dry and flat surface (e.g. table). Then perform the test as follows:<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t\"\"\t\t\t\t\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
\n\t\t\t\t
\n\t\t\t\t\t\t\t\t\t
  1. Wash your hands thoroughly.<\/strong> Use soap and warm water. Dry your hand with clean towel.<\/li>
  2. Prepare the test device and capillary pipette:<\/strong> Take them out from the protective pouch (tear at the notch) and place them in the reach of your hands (you will need them later). Discard the desiccant bag.<\/li>
  3. Prepare the lancet.<\/strong> Hold the lancet without touching the trigger button. Unlock the cap twisting it off \u00bc turn until you feel it separates from the lancet and then continue twisting it (2-3 rotations). Don\u2019t pull just twist and discard the cap when finished. \u2460\u2461<\/li>
  4. Clean the end of the middle or ring finger<\/strong> with cotton damped with alcohol. Massage the chosen finger towards the tip for 10 to 15 seconds to enhance the blood flow.<\/li>
  5. Prick the finger:<\/strong> put the lancet firmly against the side of the previously cleaned finger, and press the release trigger button.\u2462 The lancet will automatically retract into the body of the device. Gently massage the finger to create a nice round blood droplet.\u2463<\/li>
  6. Collect the blood with the capillary pipette:<\/strong> Gently touch the blood droplet with the open end of the capillary pipette. It must be filled until the line indicated on the capillary pipette. Do not press the bulb, it fills by itself. Make another blood droplet if the line is not reached. As far as possible, avoid air bubbles. \u2464<\/li>
  7. Put the blood collected with the pipette into the sample well<\/strong> of the device, by pressing on the pipette bulb. \u2465<\/li>
  8. Wait 30-40 sec<\/strong> for the blood being totally absorbed into the sample well.<\/li>
  9. Add the diluent:<\/strong> Unscrew the blue cap of the diluent dropper vial (leave the white cap tightly screwed) and add the diluent as follows: Hold the diluent dropper vial vertically and slowly add exactly 4 drops in the sample well of the device with an interval of 2-3 seconds between each drop. \u2466<\/li>
  10. Read the result after 10 minutes. Do not interpret after 15 minutes.<\/strong><\/li><\/ol>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t
    \n\t\t\t\t\t
    \n\t\t
    \n\t\t\t\t
    \n\t\t\t\t\t

    Results Interpretation<\/h2>\t\t\t\t<\/div>\n\t\t\t\t
    \n\t\t\t\t\t\t\t\t\t

    The intensity and the colour of the lines do not have any importance for the interpretation of the test results.<\/p><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t

    \n\t\t\t\t
    \n\t\t\t\t\t